Selco SIGMA Protection Line

Our company will be rest from 19^th December 2024 until 5^th January 2024. From 6^th January 2025 we will gladly offer you advice and assistance. We wish you blessed and reflective Christmas and health, luck and success for the new year. Your DSL-electronic-Team...

Selco SIGMA Protection Module S6000

	• 3 Phase Measurement • Short Circuit Protection • Over Current Protection • Over Load Protection • Reverse Power Protection • Excitation Loss Protection • Load Shedding (2 Levels) • 3 Analogue Outputs • RS485 MODBUS Slave • CAN Bus • Redundant Supply
Download Manuals (.PDF) S6000 Connection S6000 Manual S6000 Modbus RTU S6000 RS232 Commands S6000 User Interface SIGMA CAN Bus Wiring SIGMA Hyper Terminal SIGMA RS485 Bus Wiring	SIGMA is an integrated generator protection and control system. The system is of high quality, is cost effective and easy to The SELCO S6000 SIGMA IO/P Module provides data acquisition and complete protection for a single generator. The S6000 measures the voltages across all three phases as well as the current running through each phase. The voltage and current signals are digitally sampled by the built-in signal processor and converted to true RMS values. The S6000 will continuously do real-time calculations of voltage, current, frequency, active/reactive power, VA, power factor etc. The S6000 can connect to generators with or without neutral.

Selco SIGMA Control Module S6100

	• 3 Phase Measurement • Busbar Monitoring • Auto or Manual Operation • Voltage Matching • Frequency Stabilization • Auto Synchronization • Active Load sharing • Voltage Stabilization • Reactive Load sharing • Conventional Governor/AVR • Electronic Governor/AVR • Paralleling with grid/shaft generator • RS485 MODBUS Slave • CAN Bus • Redundant Power Supply
Download Manuals (.PDF) S6000 Connection S6100 Governor and AVR Interfacing S6100 Manual S6100 Modbus RTU S6100 RS232 Commands S6100 Shaft Grid Operation S6100 User Interface SIGMA CAN Bus Wiring SIGMA Hyper Terminal SIGMA RS485 Bus Wiring	SIGMA is an integrated generator protection and control system. The system is of high quality, is cost effective and easy to use. The SELCO S6100 SIGMA S/LS Module provides busbar monitoring, frequency stabilization, voltage stabilization, voltage matching, automatic synchronization and active/reactive load sharing. The S6100 has dedicated interfaces for both conventional and electronic governors and automatic voltage regulators (AVRs). Manual control is also possible though external push buttons.

Selco SIGMA User Interface S6500

	• Integrated Multimeter • SIGMA User Interface • SIGMA Remote Control • C/B Status • CAN Bus • Pin Code Protected • Redundant Supply
Download Manuals (.PDF) S6500 Connection S6500 Manual S6500 RS232 Commands S6500 User Interface SIGMA CAN Bus Wiring SIGMA Hyper Terminal SIGMA RS485 Bus Wiring UK pdf	SIGMA is an integrated generator protection and control system. The system is of high quality, is cost effective and easy to use. The SELCO S6500 SIGMA UI Module is a flush mountable user interface for the SIGMA range of modules. The S6500 fills the role of a flush mount digital multimeter as well as a configuration terminal. The S6500 will provide real-time readings of voltages, currents, active/reactive load, VA, frequency, etc. A single S6500 can support up to 16 S6000 and S6100 modules. The S6500 can be used to monitor and alter parameters in parallel with an operating SCADA system.

Selco SIGMA Power Management S6610

	• Full featured Power Manager • Load depending start and stop • 5 large consumer requests • 5 non essential load trips • Black out clearance • 2 Analogue outputs • Automatic mode/ manoeuvre mode/manual mode • Supports up to 16 generators • Includes all functions of S6500 User Interface Module • Redundant power supply
Download Manuals (.PDF) S6610 Connection S6610 Manual S6610 Modbus RTU S6610 RS232 Commands S6610 User Interface SIGMA CAN Bus Wiring SIGMA Hyper Terminal SIGMA RS485 Bus Wiring	SIGMA is an integrated generator protection and control system. The system is of high quality, is cost effective and easy to use. The S6610 PM Module provides power management functionality to the SIGMA system. In co-operation with the S6000 Input/ Output and Protection Module and S6100 Synchronizing/Load sharing Module S6610 offers load depending start and stop, large consumer request and black out clearance functionality. It is also possible to program all SIGMA modules from S6610. Programming is PIN code protected.